![]() ![]() Rehearse emergency escape plans so everyone at home knows what to do in case the alarm sounds.įurther information can be obtained from the Home Office Publication or from your local fire prevention officer.3. IMPORTANT SAFEGUARDS When using household protective devices, basic safety precautions should always be followed, including those listed below. If, when the alarm goes off, there is no sign of smoke, heat or noise to indicate that there is a fire, you should get your family into a safe place, before you start investigating.8. NUISANCE/FALSE ALARMS When sure that it is just a nuisance/false alarm, simply press the test/silence button briefly on the Alarm to silence the unit for 10 minutes. If there are any problems get a qualified electrician to inspect the house wiring and connections to the alarms.7. The alarm will stop when the button is released.(Long term storage (over 1 year) can damage the batteries such that they will not recharge when the units are re-connected to the mains supply).ĥ.1 If the unit is beeping The Alarm automatically monitors the battery every 40 seconds.A unit will operate from the mains alone, even with a fully depleted or a defective battery (and give beeps every minute), though it may not give sufficient warning of fire if the mains supply is disconnected for any reason. A red light on the cover, will flash while horn is sounding. 4.(ii) Press the test button for up to 10 seconds to ensure the sensor chamber, electronics and sounder are working. Locate battery slot in base of alarm as shown below. Remove unit as shown in “ALARM REMOVAL” section on page 2. ![]() Switch off mains power to alarm (green light on cover should go out). ![]() Regularly check that the green mains indicator light on the cover is lit.4.ĬHANGING THE BATTERY (Models Ei141RC / 144RC / 146RC only) 1. Do not open or insert anything into the alarm. Your alarm is a mains 230V AC electrical appliance. Battery Smoke Detector with Hush Feature. Installation / User Guide Smoke Alarms Regulations Specification. Do not allow paint, water or dust to contaminate your alarm. IMPORTANT INFORMATION Do not paint your alarm. Designed for applications where the budget is a key consideration and where maintenance is in the hands of the owner occupier or there is no requirement for lithium power cell back-up.ġcm INTO THE CENTRE OF THE REMOVAL SLOT SLIDE ALARM OFF BASE WITH THE SCREWDRIVER STILL INSERTED, PUSH THE LOWER HALF OF THE ALARM AWAY FROM THE SCREWDRIVER, IN THE.3. Browse through the range of products in the table below. You have selected Aico EI140 Mains Voltage Smoke & Heat Alarms.More responsive to smouldering fires (Sofas, TVs) Proven optical sensor with insect screen to reduce false alarms Third Party Accredited by BSI BS EN KM 552831 Fit in: Hallway, Landing, Living Room. Aico EI146RC Smoke Alarm Optical Aico's highly reliable, cost-effective alarm solution with Alkaline battery back-up. ![]() INSERT SCREWDRIVER INSERT A FLAT-BLADED SCREWDRIVER HORIZONTALLY APPROX. THE SLOT IS LOCATED DIRECTLY ABOVE THE ARROW. ALARM REMOVAL LOCATE REMOVAL SLOT LOCATE THE ARROW ON THE FRONT FACE OF THE ALARM. REGULAR CHECKS Look for: Constant green light Red light flash every 40 sec.2. The older version had to seperate steps that one need to do: fist detach the smoke alarm from the bracket and second, then detach the mains power, but now, it's all combined into one process.230V SMOKE & HEAT ALARMS ALKALINE BATTERY BACK-UP Ei141RC - Ionisation Ei144RC - Heat Ei146RC - Optical RECHARGEABLE LITHIUM CELL BACK-UP Ei161RC - Ionisation Ei164RC - Heat Ei166RC - Optical USER INSTRUCTIONS 1. However, I like the fact that the mains power cables actually are screwed into the bracket and the bracket becomes part of the circuitry, rather than the old version where the cables fitted directly into the smoke alarm and, as such, in order to do anything with it, one had to detach the cables, wheras now, when you detach the smoke alarm, you also detach the smoke alarm from the mains in one step, because the pins are encorporated into the actual process of affixing the smoke alarm to the bracket. It took me a long while and a lot of guess work to actually attach the bracket to the ceiling properly. However, with this, one has to put the bracket on first and then one must guess where the actual screws go in the ceiling, because you can't see where the screws go, because the bracket is hiding where the screws fit into, in the ceiling enclosure. The older version, one could screw in the screws (that holds the bracket to the ceiling) first, then put the bracket on, and then slide it, and then tighten the screws. Very hard to fit This product is very hard to fit. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |